Rifle
Showing all 86 results
-
.303/ 7.7mm Precision Throater
$32.00throater allows for precise adjustments to the reamer so you can ream to any desired throat depth.
-
.338″ Precision Throater
$32.00.338″ throater allows for precise adjustments to the reamer so you can ream to any desired throat depth.
-
17 Hornet (Hornady)
$8.00 -
17 Mach IV
$8.00 -
17 PPC
$8.00 -
17 Practical (17-223)
$8.00 -
17 Remington
$8.00 -
17 Remington .194 neck
$8.0017 Remington with Ø0.194″ Neck
-
17 Remington Fireball
$8.00 -
17-222 Remington
$8.00Neck .199 Freebore .050
Lead Angle 1.5 degrees Pilot Solid -
17-250 (17/22-250)
$8.0017-250 Remington (17/22-250 Remington) Rifle Reamer Rental
-
19 Squirrel
$8.00 -
20 Caliber Precision Throater
$32.0020 Caliber throater allows for precise adjustments to the reamer so you can ream to any desired throat depth.
-
20 Nosler
$8.00Uses 22 Nosler Gauges
-
218 Bee
$42.00 -
218 Mashburn Bee
$8.00 -
219 Donaldson Rimless
$8.00Neck .251 Freebore .110
Lead Angle 1.5º Pilot Solid -
219 Donaldson Wasp
$8.00Neck .252 Freebore .110
Lead Angle 1.5º Pilot Solid -
219 Zipper
$8.00 -
22 BR Norma/Lapua
$8.0022 BR for Norma / Lapua brass.
-
22 Center Fire Throater
$30.00Pilot: Solid
NOTE: No gauges are available for shipment with this reamer.
-
22 Cheetah MK I
$8.00 -
22 Cheetah MK II
$8.00 -
22 Creedmoor
$8.0022 Creedmoor, uses same gauges as 6.5 or 6mm Creedmoor
-
22 Dasher
$8.00Pilot Solid
-
22 Grendel
$8.00Use 6.5 Grendel gauges
-
22 Hornet
$8.00 -
22 K-Hornet
$8.00 -
22 LR, Winchester 52
$38.00reamer same dimensions as original Win. 52 Chamber
-
22 PPC USA
$8.00Neck .252 Freebore .070
Pilot Floating -
22 Precision Throater
$32.0022 Center-fire throater allow for precise adjustments to the reamer so you can ream to any desired throat depth.
-
22 Remington Jet
$8.00 -
22 Rimfire Throater
$30.00.222″
-
22-243 Middlestead
$8.00 -
22-243 Winchester
$8.00Pilot Floating
-
22-250 Remington
$8.00 -
22-284 Winchester
$8.00 -
220 Swift
$8.00 -
222 Remington .250 neck
$8.00Neck .250 Freebore 0
Lead Angle 0º Pilot Floating -
222 Remington .251 neck
$8.00Neck .251 Freebore 0
Lead Angle 0º Pilot Floating -
222 Remington Magnum
$8.00 -
223 WSSM
$8.00 -
223 Wylde
$8.00Neck .256 Freebore .060
Lead Angle 1.5º Pilot Solid -
223-300 WSM
$8.00 -
224 Vais
$38.00NOTE: No gauges are available for shipment with this reamer.
-
225 Comet
$8.00Neck .257 Pilot Solid
-
22×47 Lapua
$8.00Pilot Floating
-
256 Newton
$8.00 -
270 / 6.8mm Precision Throater
$32.00throater allows for precise adjustments to the reamer so you can ream to any desired throat depth.
-
270 Belted Newton
$42.00Not the original Newton, this is a later wildcat variation on a standard belted magnum case.
-
270-08 Ackley Improved (270-308 Win. AI)
$42.00 -
30 cal. (.308″) Precision Throater
$32.00.308″ Common American 30 caliber, throater allows for precise adjustments to the reamer so you can ream to any desired throat depth.
-
30-06 Springfield, Match
$8.00Neck: .341 | Freebore: .080 | Lead Angle: 1.5º | Pilot: Floating
-
300 Whisper
$42.00 -
308 Winchester / Lapua Match
$8.00Neck: .341″ | Freebore: .115″ | Pilot: Bushing
-
30R Blaser
$8.00 -
338 Creedmoor (338-6.5 Creedmoor)
$8.00This is not the 8.6 Blackout.
-
358 Throater
$30.00NOTE: No gauges are available for shipment with this reamer.
-
416 Throater
$30.00NOTE: No gauges are available for shipment with this reamer.
-
458 Throater
$30.00NOTE: No gauges are available for shipment with this reamer.
-
5.45×39
$8.00 -
50 BMG Match
$18.00Neck: .559 | Freebore: 0 | Lead Angle: 0º | Pilot: Bushing
No Throat on Reamer. Comes with throating reamer to set customer throat.
-
50 BMG Throater
$30.00NOTE: No gauges are available for shipment with this reamer.
-
50-70 Government
$8.00 -
6.5 PRC (Hornady)
$42.006.5 PRC (Hornady)
-
6.5 PRC AW2 Spec
$42.006.5 PRC AW2 Spec
-
6.5 PRC G.A. Precision
$42.006.5 PRC, G.A. Precision version
Freebore about .130″
No-Turn Neck
-
6.5mm Precision Throater
$32.006.5mm throater allows for precise adjustments to the reamer so you can ream to any desired throat depth.
-
6.8 TVC
$42.00 -
6.8 Western (270)
$42.00 -
6mm Precision Throater
$32.006mm throater allows for precise adjustments to the reamer so you can ream to any desired throat depth.
-
6mm/22 Nosler
$42.00Pilot Floating
NOT 24 Nosler
-
7.63mm Mauser (rifle)
$42.00Bullet Dia. .306″
-
7mm PRC
$42.00 -
7mm Precision Throater
$32.007mm throater allows for precise adjustments to the reamer so you can ream to any desired throat depth.
-
8mm Precision Throater
$32.008mm throater allows for precise adjustments to the reamer so you can ream to any desired throat depth.
-
Clear Plastic Telescoping Tube, long
$2.00Plastic tubes used to protect reamers and headspace gauges. Keeps tools from knocking into each other saving wear and tear.
This size works great for most reamers with a diameter of approximately .500″ or less x up-to 8″ length.
Overall length varies from 5″ to 8″.
-
Clear Plastic Telescoping Tube, long (10 pack)
$10.99Plastic tubes used to protect reamers and headspace gauges. Keeps tools from knocking into each other saving wear and tear.
This size works great for most reamers with a diameter of approximately .500″ or less x up-to 8″ length.
Overall length varies from 5″ to 8″. Package contains 10 complete tubes
-
FN FAL flash hider die
$18.009/16×24 LH Includes a thread alignment tool (TAT). When using a TAT make sure the tool never touches the end of the barrel, only the pilot. If the TAT is allowed to touch the muzzle it is like the tools will be damaged or you will damage your new threa
-
Forster – Trigger Guard Screw Sets
$7.49These simple tools allow you to keep the barreled action properly aligned in the stock during the inletting process. Without them it is very difficult to get a tight inlet.
- 98 Mauser
- Springfield 03, 03-A3 and Krag actions
- Remington 700, 721, 722
- Savage 110
- Winchester 70
- Sako
-
Forster Inletting Guide Screws (Stock Making)
$8.95These simple tools allow you to keep the barreled action properly aligned in the stock during the inletting process. Without them it is very difficult to get a tight inlet.
- 98 Mauser
- Springfield 03, 03-A3 and Krag actions
- Enfield 1914, 1917 and SMLE
- CZ 550 or 7.7 Jap Arisaka
- Remington 700, 721, 722
- Winchester 70 or 54
- Sako
-
Sale!
Forster Stock Makers Hand Screws (Stock Making)
$19.95These simple tools allow you to keep the barreled action properly aligned in the stock during final fitting.
Recommended by stockmakers, these Forster Stockmakers Hand Screws are used in the final accurate fitting of the stock to the action. These screws are precision made and hardened to make repeated trial fittings. Set of two.
To save time and to avoid damaged guard screws or a ruined stock, don’t attempt to inlet a stock without the proper stockmakers hand screws.
- 98 Mauser
- Remington 700, 721, 722
- Winchester 70 or 54
- Enfield P-14 or P-17
- Springfield or Krag
- Sako: Except, Model 75
- Ruger 77
- 7.7 Jap Arisaka
- 6.5 Jap
-
Gunsmith Tools, Cutters & Gauges – A Primer
$12.95Shipping Now!
We spoke with leaders in the tool making industry about the things they spend most of their time and effort educating clients about. Contributions from Clymer, Forster, Manson, JGS, PTG, SAAMI and more are all included. There are books for machinists that teach this type of information, but until now there has never been a book for gunsmiths that explains the tools of the trade and how they should be utilized. The idea is simple, answer your questions before you order any tool.
Nomenclature is important, when you talk to a reamer maker, gunsmith or client you want to know the correct terms. This indicates to those you work with that you took the time the understand the tools. It will improve your ability the sell work to customers, buy or rent the right tools for the job. You will save untold hours and dollars, don’t learning at the “School of Hard Knocks”.
When you understand tools, they work better and last much longer. This both saves money and increases profits.
What is discussed?
All types or reamers specific to firearms work
Reamer Holders
Reamer Stops
Use of Reamers
Cutting Lube
Chip Welding and how to Stop it.
Misconceptions About Reamers
Chatter and its Cures
Shotgun Chamber Tools
Forcing Cone Reamers
Shotgun Chokes
Screw Choke Tooling
Measuring for Choke Tubes
Choke Lube
Defining Headspace
Choosing the Correct Gauge
Improved Chambers and Headspace
Headspace Gauge Interchange Chart
Charts for Tooling and bushings.
EBOOK NOW AVAILABLE TOO.
-
Manson Floating Reamer Holder
$30.001/2″ straight shank for use in all Lathes and Mills.
-
Micrometer Reamer Stop
$30.00Precision, repeat-ability, and ease of use: these are the benefits of P. O. Ackley Micrometer Reamer Stop. Now you can do production runs with your Chamber Reamer, without having to index each workpiece axially. You’ll be assured of consistent headspace, chamber after chamber!
To set up, insert your Chamber Reamer shank in the Reamer Holder and tighten the two set screws. Then insert the reamer holder into the Stop Cylinder assembly (micrometer threaded Stop Cylinder with .001″ Adjustment Nut, Lock Nut and optional Plug Nut). Make a rough cut in the chamber (leave about .025″ extra material). Now, with the reamer bottomed in the rough chamber, move the Stop Cylinder assembly into contact with the work piece and secure it to the Reamer Holder with three set screws.
You can now adjust the depth of the finish cut in increments of .001″, or even less. The Adjustment Nut is marked with 25 equidistant markings around the circumference, each of which corresponds to .001″ of axial adjustment. By backing off the Adjustment Nut and re-securing the Lock Nut, then repeating the cut, you can zero in on your specified headspace measurement. Adjustments of .0005″ can be made with confidence.
We recommend use with our floating reamer holders for best results, with this rental.
.437″ straight shank for use in all Lathes and Mills.
-
Sale!
The Bolt Action; a Design Analysis
$69.95This classic title by Stuart Otteson is reprinted by Z-Hat Publishing under license from the author.
It has been fully reset using the original artwork by the author. So the text and images are clean and sharp. This is not a scanned copy but a full republishing of this valuable work. If you love bolt action rifles this book is an absolute must for your collection. It is fully illustrated and includes design information about bolt actions that will amaze you and help gunsmiths build better guns with the factory specs. at their finger tips.
Hardbound, 290 pages.
