.705″ CounterBore, Remington 700 and Similar
$26.00Interchangeable pilot Counterbore for breech of 700 style barrels, cuts the recess for the bolt head in the barrel.
Showing all 42 results
Interchangeable pilot Counterbore for breech of 700 style barrels, cuts the recess for the bolt head in the barrel.
Interchangeable pilot 11° crowning tool. A clean concentric crown increases accuracy and consistency.
Hand operated, with T-handle and pilot. Includes one cutter. If you want multiple cutters order them as add-on’s to this tool. Can be used in a Drill press or with a drill motor. Specify Caliber of pilot. 17 Caliber Muzzle Tools – facing cutter, one Handle, and choose from 4 rifle muzzle pilots in .165″,…
Interchangeable pilot center cutting tool. Useful for creating a 60° seat for various centers for turning between centers.
Barrel Thread (Accuracy International SA) M27x2.0
These Gauges permit the checking of a barrel extension and barrel headspace without the need for a BCG or even a bolt. This set for AR-10 chambered in 308 Winchester.
These Gauges permit the checking of a barrel extension and barrel headspace without the need for a BCG or even a bolt. This set for AR-10 chambered in 6.5mm, 6mm, or 22 Creedmoor. As headspace for all three is identical.
Steel Tap is used to chase or re-thread the mounting threads for AR-15 buffer tubes. 1 3/16 – 16 TPI NO AVAILABLE TAP HANDLE
These Gauges permit the checking of a barrel extension and barrel headspace without the need for a BCG or even a bolt. This set for 223 Wylde, 5.56 Nato or 223 Remington.
Steel Die is used to chase or re-thread the mounting threads on AR-15 Flash Hider. 1/2″x28
Steel Die is used to chase or re-thread the barrel mounting threads on AR-15 upper receiver. 1 1/4″x18
Simple and rigid lathe fixture that holds most common rifle bolts in a four-jaw chuck for face and locking-lug truing (both front and rear surfaces) or opening up the face to accept magnum cartridges.
Bolt Lug lapping tool applies positive pressure to the bolt face to ensure a better more consistent lapped surface.
This is a fast and easy way to measure headspace on Remington Style barrels. That means barrels with a shoulder. Threaded area (tenon) diameter must be less than 1.060″. Length of the barrel tenon from the shoulder to the back of the headspace Gauge is limited to approximately 1.00″ or less. Instructions include with this…
You may request extra pilots at $4 rental fee each. Set the quantity total that you need in the shopping cart. We do not have every imaginable pilot diameter, so we will fill all orders that we can and refund for any pilots (bushings) we cannot provide [no promise that we have what you want]….
Precision, repeat-ability, and ease of use: these are the benefits of P. O. Ackley Micrometer Reamer Stop. Now you can do production runs with your Chamber Reamer, without having to index each workpiece axially. You’ll be assured of consistent headspace, chamber after chamber! To set up, insert your Chamber Reamer shank in the Reamer Holder…
Hand operated, with T-handle and pilot. Includes one cutter. If you want multiple cutters order them as add-on’s to this tool. Can be used in a Drill press or with a drill motor. Specify Caliber of pilot.
Steel Die is used to chase or re-thread the mounting threads on muzzle brakes or suppressors. 5/8″x24
Hand operated, with T-handle and pilot. Includes one cutter. If you want multiple cutters order them as add-ons to this tool. Can be used in a Drill press or with a drill motor. 45° Cutter is for external chamfer only
Removes striker assembly in seconds for fast disassembly of all Remington bolts. Works with spring relaxed or cocked. Hook fits into the notch of the firing pin head. Rotating the lever pulls firing pin head back and locks it. Fast and easy.
Action wrench for Remington 700 actions. This is the type that slides into the rails of the action. If your action has never been off the barrel from the factory, it may be too tight for this style of wrench. You turn it with the 7/8″ Closed end wrench included in the rental.
Standard Savage actions. SPECS: 1.055″-20 TPI fits Savage 110/112. [youtube]https://youtu.be/Sz0QHdEI-8k[/youtube]
Savage Model 25 bolt actions with a barrel nut, at least the recent production guns are threaded 7/8″x20. 1.175″ round die.
Approximately 9″ long, Comes with an adapter for standard 1/4″ round drive with set screw. For use with standard throat reamers and rim-fire reamers with 1/4″ drive shank. T Handle
Comes with an adapter for standard 3/8″ square drive (as pictured), about 9 inches long. For use with most chamber reamers. Adapter can be removed to expose thread if you are using PTG or other tools that have a threaded drive end.
Hold your bolt handle aligned properly to the bolt body while welding. Product may differ from image. Suggest ordering a heat sink at the same time to protect the threats and heat treat of your bolt during welding or brazing of the new bolt handle.
Easily Drill and Tap your action for scope mounts. fits receivers from .630” to 1.440”
No products in the cart.