Savage Tools (rentals)
Showing all 16 results
-
#1 Range Rod (Gordy Gritters/Grizzly)
$14.0022-6mm (243) Specify nominal pilot diameter below.
These tools are not tapered, they utilize a pilot bushing and a dial indicator. They ship with NO pilot, most gunsmiths use the pilot bushing from their reamer.
-
#2 Range Rod (Gordy Gritters/Grizzly)
$14.00257-7mm (280/284) Specify nominal pilot diameter below.
These tools are not tapered, they utilize a pilot bushing and a dial indicator. They ship with NO pilot, most gunsmiths use the pilot bushing from their reamer.
-
#3 Range Rod (Gordy Gritters/Grizzly)
$14.0030 caliber and up. Specify nominal pilot diameter below.
These tools are not tapered, they utilize a pilot bushing and a dial indicator. They ship with NO pilot, most gunsmiths use the pilot bushing from their reamer.
-
7/8″x20 Die, Savage Model 25 Barrel Die
$15.00Savage Model 25 bolt actions with a barrel nut, at least the recent production guns are threaded 7/8×20.
1.175″ round die.
-
7/8″x20 Tap, Savage Model 25 Receiver Tap
$15.00Savage Model 25 bolt actions with a barrel nut, at least the recent production guns are threaded 7/8×20.
-
Bolt Lug Lapping Tool – 22mm X 1.5mm receiver thread
$15.00Applies spring tension to bolt face during lapping process.
-
Bolt Lug Lapping Tool – Savage Small (standard) Shank
$15.00Applies spring tension to bolt face during lapping process.
-
Manson Floating Reamer Holder
$30.001/2″ straight shank for use in all Lathes and Mills.
-
Micrometer Reamer Stop
$30.00Precision, repeat-ability, and ease of use: these are the benefits of P. O. Ackley Micrometer Reamer Stop. Now you can do production runs with your Chamber Reamer, without having to index each workpiece axially. You’ll be assured of consistent headspace, chamber after chamber!
To set up, insert your Chamber Reamer shank in the Reamer Holder and tighten the two set screws. Then insert the reamer holder into the Stop Cylinder assembly (micrometer threaded Stop Cylinder with .001″ Adjustment Nut, Lock Nut and optional Plug Nut). Make a rough cut in the chamber (leave about .025″ extra material). Now, with the reamer bottomed in the rough chamber, move the Stop Cylinder assembly into contact with the work piece and secure it to the Reamer Holder with three set screws.
You can now adjust the depth of the finish cut in increments of .001″, or even less. The Adjustment Nut is marked with 25 equidistant markings around the circumference, each of which corresponds to .001″ of axial adjustment. By backing off the Adjustment Nut and re-securing the Lock Nut, then repeating the cut, you can zero in on your specified headspace measurement. Adjustments of .0005″ can be made with confidence.
We recommend use with our floating reamer holders for best results, with this rental.
.437″ straight shank for use in all Lathes and Mills.
-
Savage 110 / 10 Barrel Nut Wrench (splined)
$15.00Savage splined barrel nut wrench.
-
Savage 110 Barrel Nut Wrench (smooth)
$15.00Savage smooth barrel nut wrench
-
Savage Receiver Tap Standard Shank
$24.00Receiver Tap for standard Savage actions.
SPECS: 1.055″-20 tpi fits Savage 110/112.
-
T Handle Reamer Extension (1/4″ round shank)
$10.00Approximately 9″ long, Comes with an adapter for standard 1/4″ round drive with set screw.
Most commonly used with standard throat reamer and rim-fire reamers. T Handle -
T Handle Reamer Extension (3/8″ square shank)
$10.00Comes with an adapter for standard 3/8″ square drive, about 9 inches long.
Adapter can be removed to expose thread if you are using PTG or other tools that have a threaded drive end.
-
Tap Wrench
$6.00for hand reaming or taps
-
Williams Scope Mount Drilling Fixture
$38.00Easily Drill and Tap your action for scope mounts.
fits receivers from .630” to 1.440”
