Mauser Tools (rentals)
Rent tools specifically designed to repair and modify Mauser rifle actions. These tools are designed to match up with the special threads utilized in the Mauser designs.
Want to lap the lugs on your 98 action? Need to chase the threads on your small ring? This is the place to find those tools.
Showing all 16 results
-
#1 Range Rod (Gordy Gritters/Grizzly)
$14.0022-6mm (243) Specify nominal pilot diameter below.
These tools are not tapered, they utilize a pilot bushing and a dial indicator. They ship with NO pilot, most gunsmiths use the pilot bushing from their reamer.
-
#2 Range Rod (Gordy Gritters/Grizzly)
$14.00257-7mm (280/284) Specify nominal pilot diameter below.
These tools are not tapered, they utilize a pilot bushing and a dial indicator. They ship with NO pilot, most gunsmiths use the pilot bushing from their reamer.
-
#3 Range Rod (Gordy Gritters/Grizzly)
$14.0030 caliber and up. Specify nominal pilot diameter below.
These tools are not tapered, they utilize a pilot bushing and a dial indicator. They ship with NO pilot, most gunsmiths use the pilot bushing from their reamer.
-
Bolt Lug Lapping Tool – 98 Mauser
$15.0098 Mauser bolt lapping fixture.
-
Bolt Lug Lapping Tool – Mini Mauser (M85)
$15.00This action has been imported under many names. It is a commercial action sized for .233 Rem. or 7.62×39 class cartridges.
Applies spring tension to bolt face during lapping process.
-
Die stock – 1.5″
$5.00for use with 1.5″ dies
-
Heat Sink, Mauser 98
$6.00Heat sink for use in 98 Mauser Bolt.
-
Large Ring Barrel Die – 98 Mauser
$35.00Barrel thread die, large ring
-
Manson Floating Reamer Holder
$30.001/2″ straight shank for use in all Lathes and Mills.
-
Micrometer Reamer Stop
$30.00Precision, repeat-ability, and ease of use: these are the benefits of P. O. Ackley Micrometer Reamer Stop. Now you can do production runs with your Chamber Reamer, without having to index each workpiece axially. You’ll be assured of consistent headspace, chamber after chamber!
To set up, insert your Chamber Reamer shank in the Reamer Holder and tighten the two set screws. Then insert the reamer holder into the Stop Cylinder assembly (micrometer threaded Stop Cylinder with .001″ Adjustment Nut, Lock Nut and optional Plug Nut). Make a rough cut in the chamber (leave about .025″ extra material). Now, with the reamer bottomed in the rough chamber, move the Stop Cylinder assembly into contact with the work piece and secure it to the Reamer Holder with three set screws.
You can now adjust the depth of the finish cut in increments of .001″, or even less. The Adjustment Nut is marked with 25 equidistant markings around the circumference, each of which corresponds to .001″ of axial adjustment. By backing off the Adjustment Nut and re-securing the Lock Nut, then repeating the cut, you can zero in on your specified headspace measurement. Adjustments of .0005″ can be made with confidence.
We recommend use with our floating reamer holders for best results, with this rental.
.437″ straight shank for use in all Lathes and Mills.
-
Receiver Tap – 98 Mauser Large Ring
$24.00Receiver Thread Tap (large ring)
-
Small Ring Mauser Barrel Die
$35.00barrel thread die (93, 95, 96)
-
Small Ring Mauser Receiver Tap
$22.00Tap for 93, 95, 96
-
Tap Wrench
$6.00for hand reaming or taps
-
Universal Bolt Welding Jig
$15.00Hold your bolt handle aligned properly to the bolt body while welding.
Product may differ from image.
Suggest ordering a heat sink at the same time to protect the threats and heat treat of your bolt during welding or brazing of the new bolt handle.
-
Williams Scope Mount Drilling Fixture
$28.00Easily Drill and Tap your action for scope mounts.
fits receivers from .630” to 1.440”
