Remington® 700 (rentals)
Showing all 20 results
-
.705″ CounterBore #1, Remington 700 and similar
$26.00Interchangeable pilot Counterbore for breech of 700 style barrels, cuts the recess for the bolt head in the barrel. Work with calibers between 22-243.
Specify pilot.
-
.705″ CounterBore, Remington 700 and similar #2
$26.00Interchangeable pilot Counterbore for breech of 700 style barrels, cuts the recess for the bolt head in the barrel. Work with calibers between 25-29.
Specify pilot.
-
.705″ CounterBore, Remington 700 and similar #3
$26.00Interchangeable pilot Counterbore for breech of 700 style barrels, cuts the recess for the bolt head in the barrel. Work with calibers between 30-49.
Specify pilot.
-
.705″ CounterBore, Remington 700 and similar #4
$26.00Interchangeable pilot Counterbore for breech of 700 style barrels, cuts the recess for the bolt head in the barrel. Work with calibers between 50 & 62.
Specify pilot.
-
#0 Range Rod (Gritters Style)
$14.0017 thru 20 Cal. Specify nominal pilot diameter below.
These tools are not tapered, they utilize a pilot bushing and a dial indicator. They ship with NO pilot, most gunsmiths use the pilot bushing from their reamer.
-
#1 Range Rod (Gordy Gritters/Grizzly)
$14.0022-6mm (243) These tools are not tapered, they utilize a pilot bushing and a dial indicator.
They ship with NO pilot, most gunsmiths use the pilot bushing from their reamer.
-
#2 Range Rod (Gordy Gritters/Grizzly)
$14.00257-7mm (280/284) These tools are not tapered, they utilize a pilot bushing and a dial indicator.
They ship with NO pilot, most gunsmiths use the pilot bushing from their reamer.
-
#3 Range Rod (Gordy Gritters/Grizzly)
$14.0030 caliber and up. These tools are not tapered, they utilize a pilot bushing and a dial indicator.
They ship with NO pilot, most gunsmiths use the pilot bushing from their reamer.
-
#4 Range Rod (Gordy Gritters – style)
$14.0050 (510) Cal. These tools are not tapered, they utilize a pilot bushing and a dial indicator.
They ship with NO pilot, most gunsmiths use the pilot bushing from their reamer. -
Bolt Lug Lapping Tool – Remington 700
$15.00 -
Chambering Gage (Badger Ordnance)
$30.00This is a fast and easy way to measure headspace on Remington Style barrels. That means barrels with a shoulder. Threaded area (tenon) diameter must be less than 1.060″. Length of the barrel tenon from the shoulder to the back of the headspace Gauge is limited to approximately 1.00″ or less. Instructions include with this rental.
-
Heat Sink, Remington 700
$6.00Heat sink for use in Remington 700 Bolt.
-
Manson Floating Reamer Holder
$30.001/2″ straight shank for use in all Lathes and Mills.
-
Micrometer Reamer Stop
$30.00Precision, repeat-ability, and ease of use: these are the benefits of P. O. Ackley Micrometer Reamer Stop. Now you can do production runs with your Chamber Reamer, without having to index each workpiece axially. You’ll be assured of consistent headspace, chamber after chamber!
To set up, insert your Chamber Reamer shank in the Reamer Holder and tighten the two set screws. Then insert the reamer holder into the Stop Cylinder assembly (micrometer threaded Stop Cylinder with .001″ Adjustment Nut, Lock Nut and optional Plug Nut). Make a rough cut in the chamber (leave about .025″ extra material). Now, with the reamer bottomed in the rough chamber, move the Stop Cylinder assembly into contact with the work piece and secure it to the Reamer Holder with three set screws.
You can now adjust the depth of the finish cut in increments of .001″, or even less. The Adjustment Nut is marked with 25 equidistant markings around the circumference, each of which corresponds to .001″ of axial adjustment. By backing off the Adjustment Nut and re-securing the Lock Nut, then repeating the cut, you can zero in on your specified headspace measurement. Adjustments of .0005″ can be made with confidence.
We recommend use with our floating reamer holders for best results, with this rental.
.437″ straight shank for use in all Lathes and Mills.
-
Remington 700 Barrel Die
$35.00Barrel Die Remington 700 1-1/16 x 16 TPI
-
Remington 700 Bolt Disassembly Tool
$15.00Removes striker assembly in seconds for fast disassembly of all Remington bolts. Works with spring relaxed or cocked. Hook fits into the notch of the firing pin head. Rotating the lever pulls firing pin head back and locks it. Fast and easy.
-
Remington 700 Receiver Tap
$26.00Receiver Tap for Remington 700 actions.
SPECS: 1 1/16″x16 tpi
-
Remington 700 Wrench (internal)
$30.00Action wrench for Remington 700 actions. This is the type that slides into the rails of the action. If your action has never been off the barrel from the factory, it may be too tight for this style of wrench.
You turn it with the 7/8″ Closed end wrench included in the rental.
-
Universal Bolt Welding Jig
$20.00Hold your bolt handle aligned properly to the bolt body while welding.
Product may differ from image.
Suggest ordering a heat sink at the same time to protect the threats and heat treat of your bolt during welding or brazing of the new bolt handle.
-
Williams Scope Mount Drilling Fixture
$38.00Easily Drill and Tap your action for scope mounts.
fits receivers from .630” to 1.440”
