Pistol Tools (rentals)

Specialty tools made just for working on handguns.
Tools found here will be taps for specialty threads found in handguns. Forcing cone cutter kits in nearly every caliber possible for revolvers and even sight pushers for several popular handguns.
Showing all 48 results
-
.38/.357 Special Throating Cutter
$36.00Uniforms the chamber throats in the cylinder of a revolver for best accuracy.
Includes 7 pilots, cuts .358
NOTE: No gauges are available for shipment with this reamer.
-
.44 Special Throating Cutter
$38.00Uniforms the chamber throats in the cylinder of a revolver for best accuracy.
Includes 7 pilots, cuts .431
NOTE: No gauges are available for shipment with this reamer.
-
.45 Cylinder Throating Cutter
$36.00Uniforms the chamber throats in the cylinder of a revolver for best accuracy.
Includes 7 pilots, cuts .452
NOTE: No gauges are available for shipment with this reamer.
-
.578″ x 28 die (45 pistol)
$18.00for specific muzzle brakes.
Includes a thread alignment tool (TAT) specify caliber at check out. When using a TAT make sure the tool never touches the end of the barrel, only the pilot.
If the TAT is allowed to touch the muzzle it is likely the tools will be damaged or you will damage your new threads. -
17 Caliber Muzzle Facing Tools
$30.00Hand operated, with T-handle and pilot.
Includes one cutter. If you want multiple cutters order them as add-on’s to this tool. Can be used in a Drill press or with a drill motor.
Specify Caliber of pilot.
17 Caliber Muzzle Tools – facing cutter, one Handle, and choose from 4 rifle muzzle pilots in .165″, .166″, .167″ and .173″ diameters. These diameters cover Rimfire, Centerfire & Airgun
You can add a 79° (11°) muzzle crowning cutter or 45° chamfer cutter at $5 each
-
1911 Front Sight Staking Tool
$20.00Used to stake 1911 front sights into the slide.
-
1911 Plunger Tube Staking Tool (Brownells tm)
$20.00Easy-to-use rental tool lets you secure the plunger tube to your frame without fear of tube crush or expensive frame damage.
Adjustable to fit all makes of frames and tubes for both installing and re-tightening. Hardened crimping point. Plunger Tube Support slips inside plunger tube and prevents compression damage while tube is being staked to frame. Steel construction provides a rigid structure. (rental only)
-
1911 Sear and Hammer Fixture
$10.001911 Sear & Hammer Jig allows you to:
- Demonstrate how the trigger / hammer parts group works
- Visually check hammer and sear engagement
- Test parts before your install them into your frame
- See the parts clearly from the top and sides
- Get that trigger right the first time.
- Modify parts for trigger jobs without the hassles of putting the part in and out of the frame.
front and back
Jigs are made in the USA out of high grade aircraft aluminum and to the same tolerances of a mil spec frames.
HAMMER, SEAR, PINS, AND GRIP SAFETY ARE NOT INCLUDED IN THIS RENTAL.
ONLY THE JIG BLOCK IS AVAILABLE to Rent!
-
45 Degree – Cylinder Chamfer Kit
$25.00Hand operated, with T-handle and pilot.
Includes one 45 degree cutter. Can be used in a Drill press or with a drill motor.
You are required to specify Caliber of pilot, these pilots are made specifically for use on Revolver cylinders, with two diameters to keep the aligned.
-
90º Breach Facing Cutter
$5.00Add on tool; for forcing cone kits, square breach of revolver barrels. Used to set the correct barrel/cylinder gap on revolvers. Order this tool with the forcing cone kit.
Sizes vary, provide us with your barrel breach diameter below.
-
Barrel Tap – Colt SAA
$15.00.695″ x 20 Thread
-
Bench Block – Ruger P series
$25.00Designed to hold the slide when changing/adjusting the sights on Ruger P series pistols and when removing or installing the extractor.
-
Colt, MGW Revolver Wrench Insert
$8.00Colt Double Action (DA), Python, E and I frames.
Delrin insert for MGW revolver wrench frame. Interchangeable, split Delrin inserts allow slight adjustment to compensate for variations in individual guns.
-
Muzzle Facing Tools
$28.00Hand operated, with T-handle and pilot.
Includes one cutter. If you want multiple cutters order them as add-on’s to this tool. Can be used in a Drill press or with a drill motor.
Specify Caliber of pilot.
-
Ruger, Security Six, MGW Revolver Wrench Insert
$8.00Security Six
Delrin insert for MGW revolver wrench frame. Interchangeable, split Delrin inserts allow slight adjustment to compensate for variations in individual guns.
-
Smith & Wesson K Frame Tap
$15.00.540” – 36 Thread
-
Smith & Wesson L Frame Tap
$15.00.562” – 36 Thread
-
Smith & Wesson N Frame Tap
$15.00.670” – 36 Thread
-
T Handle Reamer Extension
$10.00Comes with an adapter for standard 3/8″ square drive. Adapter can be removed to expose thread if you are using PTG or other tools that have a threaded drive end.
-
Tap Wrench
$6.00for hand reaming or taps
-
Xtra Pilots for Removable Pilot / Bushing Reamers
$2.00You may request extra pilots at $2 rental fee each. Set the quantity total that you need in the shopping cart.
You will need to state the exact diameters you desire in the comments area at check-out. We do not have every imaginable pilot diameter, so we will fill all orders that we can and refund for any pilots (bushings) we cannot provide [no promise that we have what you want]. (refunds occur when the order is closed out upon tool returns)