10 Minute Deer SkinnerSale!
How many times have you said, “Now that the animal is down, The fun stops and the work starts.”
Not so with this handy tool.
|•||Absolutely the fastest and easiest way to skin a deer|
|•||Keeps meat clean from hair and other contaminants|
|•||Professional method of skinning, minimal cutting and reduces nicks in hide|
|•||Uses the power of your vehicle to quickly and efficiently remove deer skin|
The 10 Minute Deer Skinner is the most time efficient method that we’ve found (using the least amount of physical effort) to take a deer from the buck pole to the deep freeze. Simply field dress your deer and placed on a clean sheet of plastic before the 10 Minute Deer Skinner is utilized.
STEP 1: Extend the skin cut on the deer from the field dressed cut to the base of head. (Two to four inches from the head.) From the end of this cut, make a complete circle around the neck, connecting with the original cut. Important: Cut skin only, not the meat.
STEP 2: Attach loop of plain cable to an immovable object (tree, stump, ball hitch of parked vehicle, etc.). Slip the loop on the other end of plain cable around the deer head, behind the ears, and hand tighten. From cut on back of neck, pull hide back toward the tail six (6) to ten (10) inches.
STEP 3: Cut skin on each front leg from knee joint to brisket cut. Make a cut circling the knee joint. Note: DO NOT PULL SKIN. Again, cut skin only, not meat. Brush hair off drop cloth, and clean area around the deer, so the skinned carcass will drop on a clean surface.
STEP 4: This step will utilize the two stage ball and skinner plate for hide removal. Take the long cable that contains the skinner plate and two stage ball and place the skinner plate (flat surface down) on the raw side of the hide. Push the small end of the two stage ball from the hair side of the hide, through the hole in the skinner plate. Hand tighten cable around the narrow section of the two stage ball by pulling only on the coated end of the cable.
STEP 5: Advance vehicle (slowly) to remove slack. Hunter should stand to the side of deer for safety reasons and to signal the driver. Vehicle should be advanced (see Figure 4) until skin is removed to the hind leg joints. Cut skin around each back leg between knee and ankle joint. Resume truck advancement (if necessary) until skin is completely removed. Your deer should be completely skinned and dropped back on a clean, plastic surface.
Note: If the animal has been down for an extended period of time, the front legs of the deer may need to be moved toward rear to permit clean skin removal around the legs. Also, if the hide is to be kept, skin tail by hand (as shown in video). Finally, if the hide is to be tanned, split each back leg open from hind quarter to end of leg.
Kit includes: Both Cables with the skinner system fully assembled and ready to use. Written instructions, a DVD with an instructional video on how to use the 10 Minute Deer Skinner and a pouch the carry it all in. Make Skinning Fun!
You may also like…
Forster Datum Dial$89.95
The Forster Datum Dial makes it possible for the handloader or gunsmith to use ordinary dial calipers to make normally difficult length measurements based on the case shoulder. By measuring cases to the datum line on the shoulder, the reloader can custom-fit the ammunition to a rifle’s chamber for the best possible fit for better accuracy potential and longer case life.
Gunsmiths can easily check the length of customers reloads verses the chamber.
This tool can also be used to double check headspace gauges if questions arise
Included are complete instructions, storage box, and a laminated chart with common datum diameters.Add to cart
Forster Inletting Guide Screws (Stock Making) – Mauser 98$8.95 Add to cart
Bubble Level, SME (Weaver Dovetail)$15.95
The SME Bubble Bore level allows the shooter to check both the rifle bore and the reticle alignment at a glance. Constructed of aircraft grade aluminum.
Specification: SME Bubble Bore Level
- Attaches to any Weaver-style rail or base.
- Ambidextrous Mounting
- Assures bore alignment at a glance.
- White line on housing for quick reference.
- Hex wrench for mounting included
Winchester 70 style, bolt knob (Dakota)$18.95
Winchester 70 type, Dakota cast bolt knobs for custom replacements. Limited quantities available.
Future availability is unknown.Add to cart