revolver
Showing all 28 results
-
.38/.357 Special Throating Cutter
$36.00Uniforms the chamber throats in the cylinder of a revolver for best accuracy.
Includes 7 pilots, cuts .358
NOTE: No gauges are available for shipment with this reamer.
-
.44 Special Throating Cutter
$38.00Uniforms the chamber throats in the cylinder of a revolver for best accuracy.
Includes 7 pilots, cuts .431
NOTE: No gauges are available for shipment with this reamer.
-
22 LR Cylinder
$38.0022 Long Rifle, Cylinder reamer for revolvers.
-
22 Winchester Magnum Cylinder
$34.00Pilot: Solid
-
38-40 WCF (cylinder)
$8.00Cylinder reamer
-
41 Special (Barrel)
$8.0041 Special is a shortened 41 Remington Magnum. Like the 38 Special and the 44 Special it is loaded lighter than the magnum versions of the caliber.
Uses 41 Magnum gauges.
-
41 Special (cylinder)
$8.0041 Special is a shortened 41 Remington Magnum. Like the 38 Special and the 44 Special it is loaded lighter than the magnum versions of the caliber.
Uses 41 Magnum gauges.
-
44 Magnum (Cylinder)
$8.0044 Magnum, for revolvers
-
45 ACP, (revolver cylinder)
$8.00Cylinder reamer
-
45 Degree – Cylinder Chamfer Kit
$25.00Hand operated, with T-handle and pilot.
Includes one 45 degree cutter. Can be used in a Drill press or with a drill motor.
You are required to specify Caliber of pilot, these pilots are made specifically for use on Revolver cylinders, with two diameters to keep the aligned.
-
Barrel Set-Back Fixture, Revolver (Brownells™)
$38.00Relieve Revolver Barrel Shoulders Without Owning A Lathe
Properly fit new factory or bull barrels, or set back existing barrels to adjust barrel/cylinder gap, without a lathe.
SPECS: Kit includes steel fixture body – 27/8″ (7.30cm) long, adjustable carbide cutter, one bore pilot, adjustable pilot carrier, and Allen wrench.
Caliber Options: .22RF, .32, .38/.357, .41, .44 and .45. Uses Barrel/Facing, Muzzle/Chamfer pilots from Brownells. -
Plug Gauges for Forcing Cones in Revolver Barrels
$6.00By simply slipping the Plug Gauge into the barrel throat, it’s possible to tell at a glance when you are approaching the correct diameter. Warns you before you go too far. Also valuable as a diagnostic tool for guns brought in with accuracy complaints, (designed for chamfers cut with our tools – may not give a correct reading on guns with other degrees of chamfer). Each gauge is self-piloted, precision-ground, hardened and stepped to show minimum and maximum optimum diameters. 11° and 18° Gauge measures both chamfer angles.
Instruction for Plug Gauges.
-
Revolver Forcing Cone Tools 22 Rimfire
$30.00Includes the 11 degree forcing cone cutter, rod, t-handle.
Add a chamfer plug gauge if you so desire.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 22 RimFire Caliber
Includes the 11 degree forcing cone cutter, rod, t-handle.
Add a chamfer plug gauge if you so desire.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 32 Caliber
$35.00Includes the 11 degree forcing cone cutter, rod, t-handle and bushing where needed.
Add a chamfer plug gauge if you so desire.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 38/357/9mm (11 degree)
$35.00Includes the 11 degree forcing cone cutter, rod, t-handle and bushing where needed.
Add a chamfer plug gauge if you so desire.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 38/357/9mm (22 degree)
$35.00Includes the 22 degree forcing cone cutter, rod, t-handle and bushing where needed. This cutter was made by PTG and fits our kits. They are marked 11 degree, but they are twice as steep as the Brownells 11 degree cutter. Results would likely be best with jacketed bullets.
Add an 11 to 18 degree chamfer plug gauge if you so desire, they work on the diameter of the forcing cone so would work for this cutter as well.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 38/357/9mm (5 degree)
$35.00Includes the 5 degree forcing cone cutter, rod, t-handle and bushing where needed.
Add a chamfer plug gauge if you so desire.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 40 Caliber (11 degree)
$35.00Includes the 11 degree forcing cone cutter, rod, t-handle and bushing where needed.
Add a chamfer plug gauge if you so desire.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 41 Caliber (11 degree)
$35.00Includes the 11 degree forcing cone cutter, rod, t-handle and bushing where needed.
Add a chamfer plug gauge if you so desire.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 41 Caliber (22 degree)
$35.00Includes the 22 degree forcing cone cutter, rod, t-handle and bushing where needed. This cutter was made by PTG and fits our kits. They are marked 11 degree, but they are twice as steep as the Brownells 11 degree cutter. Results would likely be best with jacketed bullets.
Add an 11 to 18 degree chamfer plug gauge if you so desire, they work on the diameter of the forcing cone so would work for this cutter as well.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 44 and 45 Caliber (18 degree)
$35.00Includes the 18 degree forcing cone cutter, rod, t-handle and bushing where needed.
Add a chamfer plug gauge if you so desire.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 44 Caliber (11 degree)
$35.00Includes the 11 degree forcing cone cutter, rod, t-handle and bushing where needed.
Add a chamfer plug gauge if you so desire.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 44 Caliber (22 degree)
$35.00Includes the 22 degree forcing cone cutter, rod, t-handle and bushing where needed. This cutter was made by PTG and fits our kits. They are marked 11 degree, but they are twice as steep as the Brownells 11 degree cutter. Results would likely be best with jacketed bullets.
Add an 11 to 18 degree chamfer plug gauge if you so desire, they work on the diameter of the forcing cone so would work for this cutter as well.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 45/460 Caliber (11 degree)
$35.00Includes the 11 degree forcing cone cutter, rod, t-handle and bushing where needed.
Add a chamfer plug gauge if you so desire.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 45/460 Caliber (22 degree)
$35.00Includes the 22 degree forcing cone cutter, rod, t-handle and bushing where needed. This cutter was made by PTG and fits our kits. They are marked 11 degree, but they are twice as steep as the Brownells 11 degree cutter. Results would likely be best with jacketed bullets.
Add an 11 to 18 degree chamfer plug gauge if you so desire, they work on the diameter of the forcing cone so would work for this cutter as well.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 9mm to 41 caliber (18 degree)
$35.00Includes the 18 degree forcing cone cutter, rod, t-handle and bushing where needed.
Add a chamfer plug gauge if you so desire.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Wrench (Frame)
$30.00Wrench Frame Only.
Prevents springing the frame by using fitted inserts that exactly match the contours of the revolver frame and distribute the turning forces evenly over it. Interchangeable, split Delrin inserts allow slight adjustment to compensate for variations in individual guns (inserts rented separately so you can order one or more this handle fits all the inserts).
