Handgun
Showing all 26 results
-
.32 Cal. Throating Cutter
$38.00Uniforms the chamber throats in the cylinder of a revolver for best accuracy.
Includes 7 pilots, cuts 32 caliber cylinders.
NOTE: No gauges are available for shipment with this reamer.
-
.38/.357 Special Throating Cutter
$38.00Uniforms the chamber throats in the cylinder of a revolver for best accuracy.
Includes 7 pilots, cuts .358
NOTE: No gauges are available for shipment with this reamer.
-
.45 Cylinder Throating Cutter
$38.00Uniforms the chamber throats in the cylinder of a revolver for best accuracy.
Includes 7 pilots, cuts .452
NOTE: No gauges are available for shipment with this reamer.
-
7.5mm FK Brno
$8.007.5 FK Brno
-
7.65 Luger (30 Luger)
$8.00 -
MGW Sight Pusher: 1911
$28.00Fits most any 1911 slide.
Designed to remove, install, and adjust the rear sight and not mar the handgun.
-
Plug Gauges for Forcing Cones in Revolver Barrels
$6.00By simply slipping the Plug Gauge into the barrel throat, it’s possible to tell at a glance when you are approaching the correct diameter. Warns you before you go too far. Also valuable as a diagnostic tool for guns brought in with accuracy complaints, (designed for chamfers cut with our tools – may not give a correct reading on guns with other degrees of chamfer). Each gauge is self-piloted, precision-ground, hardened and stepped to show minimum and maximum optimum diameters. 11° and 18° Gauge measures both chamfer angles.
Instruction for Plug Gauges.
-
Revolver Forcing Cone Tools 22 Rimfire
$30.00Includes the 11 degree forcing cone cutter, rod, t-handle.
Add a chamfer plug gauge if you so desire.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 32 Caliber
$35.00Includes the 11 degree forcing cone cutter, rod, t-handle and bushing where needed.
Add a chamfer plug gauge if you so desire.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 38/357/9mm (11 degree)
$35.00Includes the 11 degree forcing cone cutter, rod, t-handle and bushing where needed.
Add a chamfer plug gauge if you so desire.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 38/357/9mm (22 degree)
$35.00Includes the 22 degree forcing cone cutter, rod, t-handle and bushing where needed. This cutter was made by PTG and fits our kits. They are marked 11 degree, but they are twice as steep as the Brownells 11 degree cutter. Results would likely be best with jacketed bullets.
Add an 11 to 18 degree chamfer plug gauge if you so desire, they work on the diameter of the forcing cone so would work for this cutter as well.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 38/357/9mm (5 degree)
$35.00Includes the 5 degree forcing cone cutter, rod, t-handle and bushing where needed.
Add a chamfer plug gauge if you so desire.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 40 Caliber (11 degree)
$35.00Includes the 11 degree forcing cone cutter, rod, t-handle and bushing where needed.
Add a chamfer plug gauge if you so desire.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 41 Caliber (11 degree)
$35.00Includes the 11 degree forcing cone cutter, rod, t-handle and bushing where needed.
Add a chamfer plug gauge if you so desire.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 41 Caliber (22 degree)
$35.00Includes the 22 degree forcing cone cutter, rod, t-handle and bushing where needed. This cutter was made by PTG and fits our kits. They are marked 11 degree, but they are twice as steep as the Brownells 11 degree cutter. Results would likely be best with jacketed bullets.
Add an 11 to 18 degree chamfer plug gauge if you so desire, they work on the diameter of the forcing cone so would work for this cutter as well.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 44 and 45 Caliber (18 degree)
$35.00Includes the 18 degree forcing cone cutter, rod, t-handle and bushing where needed.
Add a chamfer plug gauge if you so desire.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 44 Caliber (11 degree)
$35.00Includes the 11 degree forcing cone cutter, rod, t-handle and bushing where needed.
Add a chamfer plug gauge if you so desire.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 44 Caliber (22 degree)
$35.00Includes the 22 degree forcing cone cutter, rod, t-handle and bushing where needed. This cutter was made by PTG and fits our kits. They are marked 11 degree, but they are twice as steep as the Brownells 11 degree cutter. Results would likely be best with jacketed bullets.
Add an 11 to 18 degree chamfer plug gauge if you so desire, they work on the diameter of the forcing cone so would work for this cutter as well.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 45/460 Caliber (11 degree)
$35.00Includes the 11 degree forcing cone cutter, rod, t-handle and bushing where needed.
Add a chamfer plug gauge if you so desire.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 45/460 Caliber (22 degree)
$35.00Includes the 22 degree forcing cone cutter, rod, t-handle and bushing where needed. This cutter was made by PTG and fits our kits. They are marked 11 degree, but they are twice as steep as the Brownells 11 degree cutter. Results would likely be best with jacketed bullets.
Add an 11 to 18 degree chamfer plug gauge if you so desire, they work on the diameter of the forcing cone so would work for this cutter as well.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 9mm to 41 caliber (18 degree)
$35.00Includes the 18 degree forcing cone cutter, rod, t-handle and bushing where needed.
Add a chamfer plug gauge if you so desire.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Wrench (Frame)
$30.00Wrench Frame Only.
Prevents springing the frame by using fitted inserts that exactly match the contours of the revolver frame and distribute the turning forces evenly over it. Interchangeable, split Delrin inserts allow slight adjustment to compensate for variations in individual guns (inserts rented separately so you can order one or more this handle fits all the inserts).
-
S&W ‘K’ Frame, MGW Revolver Wrench Insert
$8.00Smith & Wesson K Frame insert.
Delrin insert for MGW revolver wrench frame. Interchangeable, split Delrin inserts allow slight adjustment to compensate for variations in individual guns.
-
S&W ‘L’ Frame, MGW Revolver Wrench Insert
$8.00Smith & Wesson L Frame insert.
Delrin insert for MGW revolver wrench frame. Interchangeable, split Delrin inserts allow slight adjustment to compensate for variations in individual guns.
-
S&W ‘N’ Frame, MGW Revolver Wrench Insert
$8.00Smith & Wesson N Frame insert.
Delrin insert for MGW revolver wrench frame. Interchangeable, split Delrin inserts allow slight adjustment to compensate for variations in individual guns.
-
Single Action, MGW Revolver Wrench Insert
$8.00Colt SAA (P frame) or the Ruger Blackhawk
Delrin insert for MGW revolver wrench frame. Interchangeable, split Delrin inserts allow slight adjustment to compensate for variations in individual guns.