tool
Showing all 23 results
-
6-48 Tap, Plug
$4.98Irwin/Hanson brand. 6-48 Scope/Sight Gun Tap, 3 flute, Plug type, bright Carbon, Hand Tap.
-
Action Block & Lower Vise Block Set (AR-15)
$15.00Protect Receiver From Damage When Clamping
Heavy-duty blocks allow you to firmly clamp AR-15/M16 receiver halves in a vise without risk of crushing, twisting, or otherwise distorting them when applying vise pressure or torquing the barrel nut. Keeps your rifle secure for safe, effective cleaning, assembly, and repair. High pressure, solvent resistant, structural Rynite block and insert surround the entire upper receiver and support it inside and out to make rebarreling the AR-15/M16 an easy, one-man job. Lets you firmly secure a mil-spec carry handle receiver or mil-spec flattop receiver in a large bench vise for barrel removal/installation. Torque generated while tightening the barrel nut is transmitted to the block and insert, not the receiver. Minimizes the possibility of damage to the barrel detent pin and receiver detent notch. Holds securely without marring the finish.
DO NOT USE ON BILLET UPPERS OR LEFT HAND UPPERS, OR DAMAGE TO THE UPPER CAN RESULT.
-
AR-15 Front Sling Swivel Staking Tool
$15.00Make that swivel secure. Stake it properly with this rental tool.
-
AR-15 Hammer/Trigger Pin Assembly Guide set
$15.95The KNS Precision, Inc. AR15 Hammer/Trigger Pin Assembly Guide is designed to allow the user to easily install and remove the AR15/M16 trigger and hammer pins. This guide includes 2 (two) guide pins and 1 (one) pusher. This is a must have for anyone who frequently installs or removes the trigger group in their AR15 or M16.
-
Bolt Fixture, LaBounty
$36.00Simple and rigid lathe fixture that holds most common rifle bolts in a four-jaw chuck for face and locking-lug truing (both front and rear surfaces) or opening up the face to accept magnum cartridges.
-
Bolt Lug Lapping Tool – 22mm X 1.5mm receiver thread
$15.00Applies spring tension to bolt face during lapping process.
-
Bolt Lug Lapping Tool – Howa 1500 or Weatherby Vangard
$15.00Works with either the Howa 1500 or the Wby Vangard.
-
Bolt Lug Lapping Tool – Mini Mauser (M85)
$15.00This action has been imported under many names. It is a commercial action sized for .233 Rem. or 7.62×39 class cartridges.
Applies spring tension to bolt face during lapping process.
-
Bolt Lug Lapping Tool – Ruger 77
$15.00Applies spring tension to bolt face during lapping process.
1 inch x 16 threads per inch versions.
-
Bolt Lug Lapping Tool – Savage Small (standard) Shank
$15.00Applies spring tension to bolt face during lapping process.
-
Bolt Lug Lapping Tool – Winchester Model 70
$15.00Applies spring tension to bolt face during lapping process.
1 inch x 16 threads per inch versions.
-
Broken Shell Extractor 223/5.56
$6.95 -
Broken Shell Extractor 308 Win. 7.62 NATO
$8.25 -
Heat Sink, Springfield Bolt
$6.00Heat sink for use in Springfield 1903 or 03-A3 Bolt.
-
Remington 700 Bolt Disassembly Tool
$54.99Removes striker assembly in seconds for fast disassembly of all Remington bolts. Works with spring relaxed or cocked. Hook fits into the notch of the firing pin head. Rotating the lever pulls firing pin head back and locks it. Fast and easy.
-
Remington 700 Bolt Disassembly Tool
$15.00Removes striker assembly in seconds for fast disassembly of all Remington bolts. Works with spring relaxed or cocked. Hook fits into the notch of the firing pin head. Rotating the lever pulls firing pin head back and locks it. Fast and easy.
-
Shell Latch Staker
$10.00Remington 870/1100 SHELL LATCH STAKER
This tool has the correct, factory designed, rectangular swaging point to displace plenty of metal and a built-in handle, for built in control.
-
T Handle Reamer Extension (1/4″ round shank)
$10.00Approximately 9″ long, Comes with an adapter for standard 1/4″ round drive with set screw.
Most commonly used with standard throat reamer and rim-fire reamers. -
T Handle Reamer Extension (3/8″ square shank)
$10.00Comes with an adapter for standard 3/8″ square drive, about 9 inches long.
Adapter can be removed to expose thread if you are using PTG or other tools that have a threaded drive end.