Bolt
Showing all 18 results
-
‘Epoxy Sleeving’ and Lapping Bolt Lugs for Accuracy (DVD)
$49.94In this Course, Gordy Gritters, well known benchrest gunsmith and competitor, shares a previously proprietaty secret and extremely effective method of reducing bolt play in a rifle action to increase accuracy, sometimes astonishingly so!
He also goes into great detail showing a very effective method of lapping bolt lugs without wearing them at an angle like so often happens when using conventional methods.
These two techniques go hand-in-hand to correct issues that have a major impact on the accuracy of a rifle! Gordy’s clients rely on him to wring out all the accuracy possible from thier rifles, you and use the same methods to improve your guns.Another great instructional video. Return to Gordy’s expert instruction as often as you like to get every detail correct.
-
6.5mm BPC (bolt action Grendel)
$42.00Pilot Floating
More accurate for bolt action chambering.
-
Bolt Fixture, LaBounty
$36.00Simple and rigid lathe fixture that holds most common rifle bolts in a four-jaw chuck for face and locking-lug truing (both front and rear surfaces) or opening up the face to accept magnum cartridges.
-
Bolt Lug Lapping Tool – 22mm X 1.5mm receiver thread
$15.00Applies spring tension to bolt face during lapping process.
-
Bolt Lug Lapping Tool – Howa 1500 or Weatherby Vangard
$15.00Works with either the Howa 1500 or the Wby Vangard.
-
Bolt Lug Lapping Tool – Mini Mauser (M85)
$15.00This action has been imported under many names. It is a commercial action sized for .233 Rem. or 7.62×39 class cartridges.
Applies spring tension to bolt face during lapping process.
-
Bolt Lug Lapping Tool – Ruger 77
$15.00Applies spring tension to bolt face during lapping process.
1 inch x 16 threads per inch versions.
-
Bolt Lug Lapping Tool – Savage Small (standard) Shank
$15.00Applies spring tension to bolt face during lapping process.
-
Bolt Lug Lapping Tool – Winchester Model 70
$15.00Applies spring tension to bolt face during lapping process.
1 inch x 16 threads per inch versions.
-
Heat Sink, Enfield P-14 or P-17
$6.00Heat sink for use in Enfield Bolt.
-
Heat Sink, Mauser 98
$6.00Heat sink for use in 98 Mauser Bolt.
-
Heat Sink, Remington 700
$6.00Heat sink for use in Remington 700 Bolt.
-
Heat Sink, Springfield Bolt
$6.00Heat sink for use in Springfield 1903 or 03-A3 Bolt.
-
Heat Sink, Winchester 70
$6.00Heat sink for use in Winchester 70 Bolt.
-
Pillar Bedding Gunsmith Kit, Winchester 70
$49.95
Aluminum pillars machined to mate between the action and the trigger guard will eliminate any possible compression. In a sense what you are doing is putting the brunt of the load on rock solid pillars, then attaching your stock to these pillars. The single most important quality pillar bedded rifles must have is that all of its components are at rest, whether the trigger guard screws are loose or tight, I.E. stress free bedding.This easy to use kit allows the user to adjust the pillars to match the stock. You can assemble everything for bedding and know it is aligned for error proof bedding jobs.
Complete instructions included with the pillars and tools.
-
Remington 700 Bolt Disassembly Tool
$54.99Removes striker assembly in seconds for fast disassembly of all Remington bolts. Works with spring relaxed or cocked. Hook fits into the notch of the firing pin head. Rotating the lever pulls firing pin head back and locks it. Fast and easy.
-
Remington 700 Bolt Disassembly Tool
$15.00Removes striker assembly in seconds for fast disassembly of all Remington bolts. Works with spring relaxed or cocked. Hook fits into the notch of the firing pin head. Rotating the lever pulls firing pin head back and locks it. Fast and easy.
-
Remington 700 Wrench (internal)
$30.00Action wrench for Remington 700 actions. This is the type that slides into the rails of the action. If your action has never been off the barrel from the factory, it may be too tight for this style of wrench.
You turn it with the 7/8″ Closed end wrench included in the rental.
