Barrel
Showing all 98 results
-
Savage Drop-In Barrels
$0.00 -
17 Mach II
$0.00Pilot Bushing Pilot, barrel
-
22 Long Rifle (min pilot .212″)
$0.00undersized pilot for liners with small bore diameter.
-
22 LR, Winchester 52
$0.00 -
17/22 Swager
$0.00Pilot Floating
Fire 22 Long Rifle in a 17 caliber barrel, the bullet is swaged to 17 as it goes down the long tapered throat.
-
22 LR Bentz
$0.00For semi-auto 22 Long Rifle, Match chambering
-
22 Short barrel
$0.00Pilot Solid, barrel reamer for 22 Short chamber.
-
22 LR Barrel
$0.00Standard 22 Long Rifle barrel reamer.
-
35 Ackley Magnum
$0.00Pilot Floating
-
375 Whelen Ackley Improved
$0.00 -
375 H&H Ackley Improved
$0.00 -
375 Dakota
$0.00 -
38-40 WCF (B)
$0.00barrel reamer
-
12 Gauge Chamber Depth Gage for 2.75” or 3”
$5.00 -
Plug Gauges for Forcing Cones in Revolver Barrels
$6.00By simply slipping the Plug Gauge into the barrel throat, it’s possible to tell at a glance when you are approaching the correct diameter. Warns you before you go too far. Also valuable as a diagnostic tool for guns brought in with accuracy complaints, (designed for chamfers cut with our tools – may not give a correct reading on guns with other degrees of chamfer). Each gauge is self-piloted, precision-ground, hardened and stepped to show minimum and maximum optimum diameters. 11° and 18° Gauge measures both chamfer angles.
Instruction for Plug Gauges.
-
Cylinder Hone, replacement stones
$6.95Shotgun Choke and Forcing Cone Hone *Extra Hone stones, 240 grit.
-
Sale!
Tap Magic, cutting fluid, 4 oz. can
$8.86$7.95Tap Magic, 4 oz. can enough cutting fluid to do many jobs.
Works as a chamber reaming cutting fluid. -
Single Action, MGW Revolver Wrench Insert
$8.00Colt SAA (P frame) or the Ruger Blackhawk
Delrin insert for MGW revolver wrench frame. Interchangeable, split Delrin inserts allow slight adjustment to compensate for variations in individual guns.
-
S&W ‘K’ Frame, MGW Revolver Wrench Insert
$8.00Smith & Wesson K Frame insert.
Delrin insert for MGW revolver wrench frame. Interchangeable, split Delrin inserts allow slight adjustment to compensate for variations in individual guns.
-
S&W ‘L’ Frame, MGW Revolver Wrench Insert
$8.00Smith & Wesson L Frame insert.
Delrin insert for MGW revolver wrench frame. Interchangeable, split Delrin inserts allow slight adjustment to compensate for variations in individual guns.
-
S&W ‘N’ Frame, MGW Revolver Wrench Insert
$8.00Smith & Wesson N Frame insert.
Delrin insert for MGW revolver wrench frame. Interchangeable, split Delrin inserts allow slight adjustment to compensate for variations in individual guns.
-
AR-15 Barrel Wrench / Multi-tool
$10.00Multi-Tool you will need when assembling your AR.
-
AR-15 Upper Receiver Die
$12.00Steel Die is used to chase or re-thread the barrel mounting threads on AR-15 upper receiver.
1 1/4″x18
-
Williams Shotgun Bead Drilling Fixture
$12.00Easily Drill and Tap for 6-48 or 3-56 beads
-
1/2″ x 28 Tap for AR / Muzzle Brakes
$14.00Muzzle brake tap, AR-15 Flash hiders and other common brakes.
-
AR-15 Barrel Extension Wrench & guide
$15.00Wrench for installing barrel extensions on a barrel, comes with extension guide to align properly.
-
AR-10 Extension Gauges, Creedmoor
$15.00These Gauges permit the checking of a barrel extension and barrel headspace without the need for a BCG or even a bolt. This set for AR-10 chambered in 6.5mm, 6mm, or 22 Creedmoor. As headspace for all three is identical.
-
AR-10 Extension Gauges, 308 Winchester
$15.00These Gauges permit the checking of a barrel extension and barrel headspace without the need for a BCG or even a bolt. This set for AR-10 chambered in 308 Winchester.
-
7/8″x20 Tap, Savage Model 25 Receiver Tap
$15.00Savage Model 25 bolt actions with a barrel nut, at least the recent production guns are threaded 7/8×20.
-
7/8″x20 Die, Savage Model 25 Barrel Die
$15.00Savage Model 25 bolt actions with a barrel nut, at least the recent production guns are threaded 7/8×20.
1.175″ round die.
-
FN FAL flash hider die
$18.009/16×24 LH Includes a thread alignment tool (TAT). When using a TAT make sure the tool never touches the end of the barrel, only the pilot. If the TAT is allowed to touch the muzzle it is like the tools will be damaged or you will damage your new threa
-
20 – 16 Gauge Adjustable Choke Reamer
$20.00.593″ – .656″
-
#7 Hinge Pin Reamer
$20.00includes 1 hinge pin with rental
-
16 – 12 Gauge Adjustable Choke Reamer
$20.00.656″ – .718″
Used to remove or modify fixed choke in barrel.
-
12 – 10 Gauge Adjustable Choke Reamer
$20.00.718″ – .781″
Used to modify or remove fixed choke from barrel
-
Cylinder/Brake Hone
$20.95Shotgun Choke and Forcing Cone Hone *Extra Hone stones, 240 grit.
Can also be used on chokes.
-
20 – 10 Gauge muzzle facing tool
$24.00Order appropriate bushings.
-
Remington 700 Receiver Tap
$24.00Receiver Tap for Remington 700 actions.
SPECS: 1 1/16″x16 tpi
-
Round or Radius Crowning Tool #1 – 22-.243 caliber
$26.00Interchangeable pilot crowning tool for calibers from 22 to 6mm.
-
Round or Radius Crowning Tool #2 – caliber 25 to 284 (7mm)
$26.00Interchangeable pilot crowning tool for calibers from 25-284 (7mm).
-
Round or Radius Crowning Tool #3, 30-458 caliber
$26.00Interchangeable pilot crowning tool for calibers from 30-458 caliber.
-
.705″ CounterBore, Remington 700 and similar #3
$26.00Interchangeable pilot Counterbore for breech of 700 style barrels, cuts the recess for the bolt head in the barrel. Work with calibers between 30-49.
Specify pilot.
-
.705″ CounterBore #1, Remington 700 and similar
$26.00Interchangeable pilot Counterbore for breech of 700 style barrels, cuts the recess for the bolt head in the barrel. Work with calibers between 22-243.
Specify pilot.
-
.705″ CounterBore, Remington 700 and similar #2
$26.00Interchangeable pilot Counterbore for breech of 700 style barrels, cuts the recess for the bolt head in the barrel. Work with calibers between 25-29.
Specify pilot.
-
.705″ CounterBore, Remington 700 and similar #4
$26.00Interchangeable pilot Counterbore for breech of 700 style barrels, cuts the recess for the bolt head in the barrel. Work with calibers between 50 & 62.
Specify pilot.
-
Williams Scope Mount Drilling Fixture
$28.00Easily Drill and Tap your action for scope mounts.
fits receivers from .630” to 1.440”
-
22 Rimfire Throater
$30.00 -
12 Gauge 55º Headspace Ring Reamer
$30.00includes 1 headspace ring
-
Manson Floating Reamer Holder
$30.001/2″ straight shank for use in all Lathes and Mills.
-
Revolver Forcing Cone Tools 22 Rimfire
$30.00Includes the 11 degree forcing cone cutter, rod, t-handle.
Add a chamfer plug gauge if you so desire.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Micrometer Reamer Stop
$30.00Precision, repeat-ability, and ease of use: these are the benefits of P. O. Ackley Micrometer Reamer Stop. Now you can do production runs with your Chamber Reamer, without having to index each workpiece axially. You’ll be assured of consistent headspace, chamber after chamber!
To set up, insert your Chamber Reamer shank in the Reamer Holder and tighten the two set screws. Then insert the reamer holder into the Stop Cylinder assembly (micrometer threaded Stop Cylinder with .001″ Adjustment Nut, Lock Nut and optional Plug Nut). Make a rough cut in the chamber (leave about .025″ extra material). Now, with the reamer bottomed in the rough chamber, move the Stop Cylinder assembly into contact with the work piece and secure it to the Reamer Holder with three set screws.
You can now adjust the depth of the finish cut in increments of .001″, or even less. The Adjustment Nut is marked with 25 equidistant markings around the circumference, each of which corresponds to .001″ of axial adjustment. By backing off the Adjustment Nut and re-securing the Lock Nut, then repeating the cut, you can zero in on your specified headspace measurement. Adjustments of .0005″ can be made with confidence.
We recommend use with our floating reamer holders for best results, with this rental.
.437″ straight shank for use in all Lathes and Mills.
-
Revolver Wrench (Frame)
$30.00Wrench Frame Only.
Prevents springing the frame by using fitted inserts that exactly match the contours of the revolver frame and distribute the turning forces evenly over it. Interchangeable, split Delrin inserts allow slight adjustment to compensate for variations in individual guns (inserts rented separately so you can order one or more this handle fits all the inserts).
-
20 Gauge 55º Headspace Ring Reamer
$30.00You will have to fabricate your own ring.
-
Revolver Forcing Cone Tools 32 Caliber
$30.00Includes the 11 degree forcing cone cutter, rod, t-handle and bushing where needed.
Add a chamfer plug gauge if you so desire.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 38/357/9mm (11 degree)
$30.00Includes the 11 degree forcing cone cutter, rod, t-handle and bushing where needed.
Add a chamfer plug gauge if you so desire.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 40 Caliber (11 degree)
$30.00Includes the 11 degree forcing cone cutter, rod, t-handle and bushing where needed.
Add a chamfer plug gauge if you so desire.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 41 Caliber (11 degree)
$30.00Includes the 11 degree forcing cone cutter, rod, t-handle and bushing where needed.
Add a chamfer plug gauge if you so desire.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 44 Caliber (11 degree)
$30.00Includes the 11 degree forcing cone cutter, rod, t-handle and bushing where needed.
Add a chamfer plug gauge if you so desire.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 45/460 Caliber (11 degree)
$30.00Includes the 11 degree forcing cone cutter, rod, t-handle and bushing where needed.
Add a chamfer plug gauge if you so desire.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Remington 700 Wrench (internal)
$30.00Action wrench for Remington 700 actions. This is the type that slides into the rails of the action. If your action has never been off the barrel from the factory, it may be too tight for this style of wrench.
You turn it with the 7/8″ Closed end wrench included in the rental.
-
Revolver Forcing Cone Tools 9mm to 41 caliber (18 degree)
$30.00Includes the 18 degree forcing cone cutter, rod, t-handle and bushing where needed.
Add a chamfer plug gauge if you so desire.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 44 and 45 Caliber (18 degree)
$30.00Includes the 18 degree forcing cone cutter, rod, t-handle and bushing where needed.
Add a chamfer plug gauge if you so desire.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 38/357/9mm (5 degree)
$30.00Includes the 5 degree forcing cone cutter, rod, t-handle and bushing where needed.
Add a chamfer plug gauge if you so desire.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 45/460 Caliber (22 degree)
$30.00Includes the 22 degree forcing cone cutter, rod, t-handle and bushing where needed. This cutter was made by PTG and fits our kits. They are marked 11 degree, but they are twice as steep as the Brownells 11 degree cutter. Results would likely be best with jacketed bullets.
Add an 11 to 18 degree chamfer plug gauge if you so desire, they work on the diameter of the forcing cone so would work for this cutter as well.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 44 Caliber (22 degree)
$30.00Includes the 22 degree forcing cone cutter, rod, t-handle and bushing where needed. This cutter was made by PTG and fits our kits. They are marked 11 degree, but they are twice as steep as the Brownells 11 degree cutter. Results would likely be best with jacketed bullets.
Add an 11 to 18 degree chamfer plug gauge if you so desire, they work on the diameter of the forcing cone so would work for this cutter as well.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 41 Caliber (22 degree)
$30.00Includes the 22 degree forcing cone cutter, rod, t-handle and bushing where needed. This cutter was made by PTG and fits our kits. They are marked 11 degree, but they are twice as steep as the Brownells 11 degree cutter. Results would likely be best with jacketed bullets.
Add an 11 to 18 degree chamfer plug gauge if you so desire, they work on the diameter of the forcing cone so would work for this cutter as well.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 38/357/9mm (22 degree)
$30.00Includes the 22 degree forcing cone cutter, rod, t-handle and bushing where needed. This cutter was made by PTG and fits our kits. They are marked 11 degree, but they are twice as steep as the Brownells 11 degree cutter. Results would likely be best with jacketed bullets.
Add an 11 to 18 degree chamfer plug gauge if you so desire, they work on the diameter of the forcing cone so would work for this cutter as well.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 22 RimFire Caliber
$30.00Includes the 11 degree forcing cone cutter, rod, t-handle.
Add a chamfer plug gauge if you so desire.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
17 Hi-Standard
$34.00NOTE: No gauges are available for shipment with this reamer.
-
Barrel Set-Back Fixture, Revolver (Brownells™)
$38.00Relieve Revolver Barrel Shoulders Without Owning A Lathe
Properly fit new factory or bull barrels, or set back existing barrels to adjust barrel/cylinder gap, without a lathe.
SPECS: Kit includes steel fixture body – 27/8″ (7.30cm) long, adjustable carbide cutter, one bore pilot, adjustable pilot carrier, and Allen wrench.
Caliber Options: .22RF, .32, .38/.357, .41, .44 and .45. Uses Barrel/Facing, Muzzle/Chamfer pilots from Brownells. -
12 Gauge Tru-Choke Tap & Reamer
$54.00Reamer, Tap and 5 bushings
Which Choke Tube Style Should I Thread My Barrel for?
Rem-Choke® & Win-Choke® style tubes are thicker and generally more available in local sporting goods stores.
Tru-Choke™ Standard tubes are thinner, and Tru-Choke™ Thinwall style tubes are thinner yet, so a wider range of barrels can be threaded to accept them. But they are less available. Check “Screw-in Choke Installation Requirements” to make sure your barrel will work with the selected style of choke tubes.
If you have never used these tools click here before ordering.
-
12 Gauge Tru-Choke Thinwall Tap & Reamer
$54.00Reamer, Tap and 5 bushings
Which Choke Tube Style Should I Thread My Barrel for?
Rem-Choke® & Win-Choke® style tubes are thicker and generally more available in local sporting goods stores.
Tru-Choke™ Standard tubes are thinner, and Tru-Choke™ Thinwall style tubes are thinner yet, so a wider range of barrels can be threaded to accept them. But they are less available. Check “Screw-in Choke Installation Requirements” to make sure your barrel will work with the selected style of choke tubes.
If you have never used these tools click here before ordering.
-
20 Gauge Tru-Choke Tap & Reamer
$54.00Reamer, Tap and 5 bushings
Which Choke Tube Style Should I Thread My Barrel for?
Rem-Choke® & Win-Choke® style tubes are thicker and generally more available in local sporting goods stores.
Tru-Choke™ Standard tubes are thinner, and Tru-Choke™ Thinwall style tubes are thinner yet, so a wider range of barrels can be threaded to accept them. But they are less available. Check “Screw-in Choke Installation Requirements” to make sure your barrel will work with the selected style of choke tubes.
If you have never used these tools click here before ordering.
-
20 Gauge Win-Choke Tap & Reamer
$54.00Reamer, Tap and 5 bushings
Which Choke Tube Style Should I Thread My Barrel for?
Rem-Choke® & Win-Choke® style tubes are thicker and generally more available in local sporting goods stores.
Tru-Choke™ Standard tubes are thinner, and Tru-Choke™ Thinwall style tubes are thinner yet, so a wider range of barrels can be threaded to accept them. But they are less available. Check “Screw-in Choke Installation Requirements” to make sure your barrel will work with the selected style of choke tubes.
If you have never used these tools click here before ordering.
-
20 Gauge Rem-Choke Tap & Reamer
$54.00Reamer, Tap and 5 bushings
Which Choke Tube Style Should I Thread My Barrel for?
Rem-Choke® & Win-Choke® style tubes are thicker and generally more available in local sporting goods stores.
Tru-Choke™ Standard tubes are thinner, and Tru-Choke™ Thinwall style tubes are thinner yet, so a wider range of barrels can be threaded to accept them. But they are less available. Check “Screw-in Choke Installation Requirements” to make sure your barrel will work with the selected style of choke tubes.
If you have never used these tools click here before ordering.
-
12 Gauge Rem-Choke Tap & Reamer
$54.00Reamer, Tap and 5 bushings
Which Choke Tube Style Should I Thread My Barrel for?
Rem-Choke® & Win-Choke® style tubes are thicker and generally more available in local sporting goods stores.
Tru-Choke™ Standard tubes are thinner, and Tru-Choke™ Thinwall style tubes are thinner yet, so a wider range of barrels can be threaded to accept them. But they are less available. Check “Screw-in Choke Installation Requirements” to make sure your barrel will work with the selected style of choke tubes.
If you have never used these tools click here before ordering.
-
12 Gauge Win-Choke Tap & Reamer
$54.00Reamer, Tap and 5 bushings
Which Choke Tube Style Should I Thread My Barrel for?
Rem-Choke® & Win-Choke® style tubes are thicker and generally more available in local sporting goods stores.
Tru-Choke™ Standard tubes are thinner, and Tru-Choke™ Thinwall style tubes are thinner yet, so a wider range of barrels can be threaded to accept them. But they are less available. Check “Screw-in Choke Installation Requirements” to make sure your barrel will work with the selected style of choke tubes.
If you have never used these tools click here before ordering.
-
12 GA. Hydraulic Dent Raiser
$60.00includes instructions
-
20 GA. Hydraulic Dent Raiser
$60.00includes instructions
-
16 GA. Hydraulic Dent Raiser
$60.00includes instructions
-
308 Barrel Blank, 25″ 1-8
$159.95raw barrel blank. 4140 Chromoly steel,25″ x 1.25″, 7.62mm/.308 caliber, 1:8 twist, button rifled, thermo stress relieved, air gauged.
We stock these blanks primarily to make Savage pre-fit barrels.
If you have us make this into a Savage barrel the end price will be the same as those listed for finished barrels. Blanks will always finish 1″ short than full length. -
25-20 Barrel Blank
$159.951-14 twist, Chromoly (blue steel), 25″ unturned blank
-
350 Legend Barrel blank
$159.9522″ long barrel blank for 350 Legend, 1-16 twist. Turned on centers, air gauged, stress relieved, and button rifled. Made of stainless steel.
We stock these blanks primarily to make Savage pre-fit barrels.
If you have us make this into a Savage barrel the end price will be the same as those listed for finished barrels. Blanks will always finish 1″ short than full length. -
338 Barrel Blank, 25″ 1-10
$169.95338 Caliber 1:10 twist Barrel Blank, 25″ long, 1.20″ diameter, 4140 chrome-moly steel, button rifled, stress relieved, precision air gauged. .330 bore / .338 groove
We stock these blanks primarily to make Savage pre-fit barrels.
If you have us make this into a Savage barrel the end price will be the same as those listed for finished barrels. Blanks will always finish 1″ short than full length. -
20/204 (5mm) Caliber Barrel Blank, 1-12, 25″
$169.9525″ x 1.0″, Chromoly, 20 Caliber, 1:12 twist premium process round barrel blank, button rifled, stress relieved, air gauged to .0002″, trimmed to length and stamped at breech with caliber and twist rate.
-
22 Center Fire Barrel Blank, 1-12
$179.00223 1:12 twist Barrel Blank, 27″ long x 1.20″ diameter, 4150 Chrome-moly, button rifled, stress relieved, precision air gauged. Turned on center for egocentricity .220 bore / .224 groove
We stock these blanks primarily to make Savage pre-fit barrels.
If you have us make this into a Savage barrel the end price will be the same as those listed for finished barrels. Blanks will always finish 1″ short than full length. -
338 Barrel Blank, 27″ 1-10
$179.00338 Caliber 1:10 twist Barrel Blank, 27″ long, 1.20″ diameter, 4140 chrome-moly steel, button rifled, stress relieved, precision air gauged. .330 bore / .338 groove
We stock these blanks primarily to make Savage pre-fit barrels.
If you have us make this into a Savage barrel the end price will be the same as those listed for finished barrels. Blanks will always finish 1″ short than full length. -
358 Barrel Blank, 27″ 1-14
$179.0027″x 1.20″ 358 caliber 1:14 twist .350 bore/ .358 groove barrel blank. Turned on centers, air gauged, stress relieved, and button rifled. Made of 4140 Chrome-moly steel.
We stock these blanks primarily to make Savage pre-fit barrels.
If you have us make this into a Savage barrel the end price will be the same as those listed for finished barrels. Blanks will always finish 1″ short than full length. -
243 (6mm) Barrel Blank, 27″ 1-10
$179.00243 caliber 1:10 twist Barrel Blank, 27″ long x 1.20″ diameter, 4140 chrome-moly steel, button rifled, stress relieved, precision air gauged. .238 bore / .244 groove
We stock these blanks primarily to make Savage pre-fit barrels.
If you have us make this into a Savage barrel the end price will be the same as those listed for finished barrels. Blanks will always finish 1″ short than full length. -
17 Rimfire Barrel Blank, 25″ 1-9
$179.95.17 Hornady Caliber, 1:9 twist – 25″ Round Barrel Blanks – Button Rifled, 4140 Chrome-Moly, 1.062″ Diameter, turned on centers, machine finish. Stress relieved & Air gauged to +/- .0002″. .169 bore / .173 groove diameters.
We can have this blank turned for your gun.
-
17 Rimfire Stainless Barrel Blank, 21″ x .920″ dia, 1-9
$179.95.17 Hornady Caliber, 1:9 twist – 21″ Round Barrel Blanks – Button Rifled, 416 Stainless, .920″ Diameter, turned on centers, machine finish. Stress relieved & Air gauged to +/- .0002″. .169 bore / .173 groove diameters.
We can have this blank turned for your gun.
-
20/204 (5mm) Caliber Barrel Blank, 1-12, 25″
$179.9525″ x 1.0″ 416 Stainless 20 Caliber, 1:12 twist premium process round barrel blank, turned on centers for concentricity, button rifled, stress relieved, air gauged to .0002″, trimmed to length and stamped at breech with caliber and twist rate.
-
6.5mm Barrel Stainless Blank, 25″ 1-9
$189.956.5mm round barrel blank, 25″ x 1.06″ 416 stainless, 1:9 twist. This premium process barrel blank is button rifled, thermo stress relieved, precision air gauged to .0002″, trimmed and stamped with caliber and twist rate at breech end. Bore .257 Groove .266
We stock these blanks primarily to make Savage pre-fit barrels.
If you have us make this into a Savage barrel the end price will be the same as those listed for finished barrels. Blanks will always finish 1″ short than full length. -
20/204 (5mm) Caliber Barrel Blank, 1-12
$189.9527″ x 1.060″ 416 Stainless 20 Caliber, 1:12 twist premium process round barrel blank, turned on centers for concentricity, button rifled, stress relieved, air gauged to .0002″, trimmed to length and stamped at breech with caliber and twist rate.
We stock these blanks primarily to make Savage pre-fit barrels.
If you have us make this into a Savage barrel the end price will be the same as those listed for finished barrels. Blanks will always finish 1″ short than full length. -
Savage Pre-fit 30 caliber Barrel Blank (unchambered), 17″ 1-10
$285.95.308 / 7.62 caliber unchambered blank, 17″ Savage Magnum taper, Standard shank, Chrome-moly, button rifled, thermo stress relieved, air gauged, muzzle stamp, .300″ bore / .3085 groove. In the white (unblued).
This barrel is threaded and tapered for a Savage bolt action, it still needs a chamber and crown. This allows you to choose the cartridge it is chambered for. Normally we can ship such barrels in as little as a week.
-
Savage Pre-fit 30 caliber Barrel Blank (unchambered), 17″ 1-10
$285.95.308 / 7.62 caliber unchambered blank, 17″ Savage Sporter taper, Standard shank, Chrome-moly, button rifled, thermo stress relieved, air gauged, muzzle stamp, .300″ bore / .3085 groove. In the white (unblued).
This barrel is threaded and tapered for a Savage bolt action, it still needs a chamber and crown. This allows you to choose the cartridge it is chambered for. Normally we can ship such barrels in as little as a week.
-
Sale!
Savage Pre-Fit 22-250 Remington Barrel, 1-8
$360.00$345.0022-250 Remington Caliber, 1:8 Twist, Savage pre-fit, 20″ long Savage Bull Taper, standard shank, 416 Stainless steel, button rifled, stress relieved, precision air gauged. .220 bore / .224 groove. 11 Degree target crown.
This barrel could be reamed for 22-250 Ackley Improved.
Savage Pre-Fit barrels can ship within 24 hours.
-
Sale!
Savage pre-fit 300 AAC Blackout Barrel 16.5″ 1-8
$410.00$385.00Savage Varmint taper pre-fit barrel, 4140 Chromoly steel, 16.5″ 300 AAC Blackout caliber, 1:8 twist, button rifled, thermo stress relieved, air gauged. This barrel is in the white (no bluing).
Muzzle is threaded 5/8″x24 for muzzle brake or suppressor.
Savage Pre-Fit barrels can ship within 24 hours.