Medium Box
Showing all 25 results
-
#1 Range Rod (Gordy Gritters/Grizzly)
$14.0022-6mm (243) Specify nominal pilot diameter below.
These tools are not tapered, they utilize a pilot bushing and a dial indicator. They ship with NO pilot, most gunsmiths use the pilot bushing from their reamer.
-
#2 Range Rod (Gordy Gritters/Grizzly)
$14.00257-7mm (280/284) Specify nominal pilot diameter below.
These tools are not tapered, they utilize a pilot bushing and a dial indicator. They ship with NO pilot, most gunsmiths use the pilot bushing from their reamer.
-
#3 Range Rod (Gordy Gritters/Grizzly)
$14.0030 caliber and up. Specify nominal pilot diameter below.
These tools are not tapered, they utilize a pilot bushing and a dial indicator. They ship with NO pilot, most gunsmiths use the pilot bushing from their reamer.
-
Action Block & Lower Vise Block Set (AR-15)
$15.00Protect Receiver From Damage When Clamping
Heavy-duty blocks allow you to firmly clamp AR-15/M16 receiver halves in a vise without risk of crushing, twisting, or otherwise distorting them when applying vise pressure or torquing the barrel nut. Keeps your rifle secure for safe, effective cleaning, assembly, and repair. High pressure, solvent resistant, structural Rynite block and insert surround the entire upper receiver and support it inside and out to make rebarreling the AR-15/M16 an easy, one-man job. Lets you firmly secure a mil-spec carry handle receiver or mil-spec flattop receiver in a large bench vise for barrel removal/installation. Torque generated while tightening the barrel nut is transmitted to the block and insert, not the receiver. Minimizes the possibility of damage to the barrel detent pin and receiver detent notch. Holds securely without marring the finish.
DO NOT USE ON BILLET UPPERS OR LEFT HAND UPPERS, OR DAMAGE TO THE UPPER CAN RESULT.
-
AR-15 Barrel Wrench / Multi-tool
$10.00Multi-Tool you will need when assembling your AR.
-
Barrel Set-Back Fixture, Revolver (Brownells™)
$38.00Relieve Revolver Barrel Shoulders Without Owning A Lathe
Properly fit new factory or bull barrels, or set back existing barrels to adjust barrel/cylinder gap, without a lathe.
SPECS: Kit includes steel fixture body – 27/8″ (7.30cm) long, adjustable carbide cutter, one bore pilot, adjustable pilot carrier, and Allen wrench.
Caliber Options: .22RF, .32, .38/.357, .41, .44 and .45. Uses Barrel/Facing, Muzzle/Chamfer pilots from Brownells. -
Die stock – 1.5″
$5.00for use with 1.5″ dies
-
Premium Manson Muzzle Facing Kit
$50.00Hand operated, with T-handle and pilot.
Includes one cutter. If you want multiple cutters order them as add-ons to this tool. Can be used in a Drill press or with a drill motor.
45° Cutter is for external chamfer only
-
Preval® Sprayer Kit
$7.99Complete Sprayer Kit
Sprayer is a professional grade spray system that is good for countless applications, disposable, recyclable, easy to clean. Use anywhere and any time no compressor is needed.
-
Remington 700 Wrench (internal)
$30.00Action wrench for Remington 700 actions. This is the type that slides into the rails of the action. If your action has never been off the barrel from the factory, it may be too tight for this style of wrench.
You turn it with the 7/8″ Closed end wrench included in the rental.
-
Revolver Forcing Cone Tools 22 Rimfire
$30.00Includes the 11 degree forcing cone cutter, rod, t-handle.
Add a chamfer plug gauge if you so desire.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 32 Caliber
$35.00Includes the 11 degree forcing cone cutter, rod, t-handle and bushing where needed.
Add a chamfer plug gauge if you so desire.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 38/357/9mm (11 degree)
$35.00Includes the 11 degree forcing cone cutter, rod, t-handle and bushing where needed.
Add a chamfer plug gauge if you so desire.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 38/357/9mm (22 degree)
$35.00Includes the 22 degree forcing cone cutter, rod, t-handle and bushing where needed. This cutter was made by PTG and fits our kits. They are marked 11 degree, but they are twice as steep as the Brownells 11 degree cutter. Results would likely be best with jacketed bullets.
Add an 11 to 18 degree chamfer plug gauge if you so desire, they work on the diameter of the forcing cone so would work for this cutter as well.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 38/357/9mm (5 degree)
$35.00Includes the 5 degree forcing cone cutter, rod, t-handle and bushing where needed.
Add a chamfer plug gauge if you so desire.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 40 Caliber (11 degree)
$35.00Includes the 11 degree forcing cone cutter, rod, t-handle and bushing where needed.
Add a chamfer plug gauge if you so desire.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 41 Caliber (11 degree)
$35.00Includes the 11 degree forcing cone cutter, rod, t-handle and bushing where needed.
Add a chamfer plug gauge if you so desire.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 41 Caliber (22 degree)
$35.00Includes the 22 degree forcing cone cutter, rod, t-handle and bushing where needed. This cutter was made by PTG and fits our kits. They are marked 11 degree, but they are twice as steep as the Brownells 11 degree cutter. Results would likely be best with jacketed bullets.
Add an 11 to 18 degree chamfer plug gauge if you so desire, they work on the diameter of the forcing cone so would work for this cutter as well.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 44 and 45 Caliber (18 degree)
$35.00Includes the 18 degree forcing cone cutter, rod, t-handle and bushing where needed.
Add a chamfer plug gauge if you so desire.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 44 Caliber (11 degree)
$35.00Includes the 11 degree forcing cone cutter, rod, t-handle and bushing where needed.
Add a chamfer plug gauge if you so desire.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 44 Caliber (22 degree)
$35.00Includes the 22 degree forcing cone cutter, rod, t-handle and bushing where needed. This cutter was made by PTG and fits our kits. They are marked 11 degree, but they are twice as steep as the Brownells 11 degree cutter. Results would likely be best with jacketed bullets.
Add an 11 to 18 degree chamfer plug gauge if you so desire, they work on the diameter of the forcing cone so would work for this cutter as well.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 45/460 Caliber (11 degree)
$35.00Includes the 11 degree forcing cone cutter, rod, t-handle and bushing where needed.
Add a chamfer plug gauge if you so desire.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 45/460 Caliber (22 degree)
$35.00Includes the 22 degree forcing cone cutter, rod, t-handle and bushing where needed. This cutter was made by PTG and fits our kits. They are marked 11 degree, but they are twice as steep as the Brownells 11 degree cutter. Results would likely be best with jacketed bullets.
Add an 11 to 18 degree chamfer plug gauge if you so desire, they work on the diameter of the forcing cone so would work for this cutter as well.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Forcing Cone Tools 9mm to 41 caliber (18 degree)
$35.00Includes the 18 degree forcing cone cutter, rod, t-handle and bushing where needed.
Add a chamfer plug gauge if you so desire.
If you want a 90 degree cutter add that as a separate item here and indicate the diameter you need.
-
Revolver Wrench (Frame)
$30.00Wrench Frame Only.
Prevents springing the frame by using fitted inserts that exactly match the contours of the revolver frame and distribute the turning forces evenly over it. Interchangeable, split Delrin inserts allow slight adjustment to compensate for variations in individual guns (inserts rented separately so you can order one or more this handle fits all the inserts).
