tool
Showing all 23 results
-
#2 Dish Type Crowning Tool 0.420 Dia
$28.00Interchangeable pilot crowning tool, 25 cal. – 7mm caliber.
Dish Diameter of 0.420″
-
#2 Dish Type Crowning Tool 0.485 Dia
$28.00Interchangeable pilot crowning tool, 25 cal. – 7mm caliber.
Dish Diameter of 0.485″
-
Action Block & Lower Vise Block Set (AR-15)
$15.00Protect Receiver From Damage When Clamping
Heavy-duty blocks allow you to firmly clamp AR-15/M16 receiver halves in a vise without risk of crushing, twisting, or otherwise distorting them when applying vise pressure or torquing the barrel nut. Keeps your rifle secure for safe, effective cleaning, assembly, and repair. High pressure, solvent resistant, structural Rynite block and insert surround the entire upper receiver and support it inside and out to make rebarreling the AR-15/M16 an easy, one-man job. Lets you firmly secure a mil-spec carry handle receiver or mil-spec flattop receiver in a large bench vise for barrel removal/installation. Torque generated while tightening the barrel nut is transmitted to the block and insert, not the receiver. Minimizes the possibility of damage to the barrel detent pin and receiver detent notch. Holds securely without marring the finish.
DO NOT USE ON BILLET UPPERS OR LEFT HAND UPPERS, OR DAMAGE TO THE UPPER CAN RESULT.
-
Bolt Fixture, LaBounty
$36.00Simple and rigid lathe fixture that holds most common rifle bolts in a four-jaw chuck for face and locking-lug truing (both front and rear surfaces) or opening up the face to accept magnum cartridges.
-
Bolt Lug Lapping Tool – 22mm X 1.5mm receiver thread
$15.00Applies spring tension to bolt face during lapping process.
-
Bolt Lug Lapping Tool – Howa 1500 or Weatherby Vangard
$15.00Works with either the Howa 1500 or the Wby Vangard.
-
Bolt Lug Lapping Tool – Mini Mauser (M85)
$15.00This action has been imported under many names. It is a commercial action sized for .233 Rem. or 7.62×39 class cartridges.
Applies spring tension to bolt face during lapping process.
-
Bolt Lug Lapping Tool – Ruger 77
$15.00Applies spring tension to bolt face during lapping process.
1 inch x 16 threads per inch versions.
-
Bolt Lug Lapping Tool – Savage Small (standard) Shank
$15.00Applies spring tension to bolt face during lapping process.
-
Bolt Lug Lapping Tool – Winchester Model 70
$15.00Applies spring tension to bolt face during lapping process.
1 inch x 16 threads per inch versions.
-
Broken Shell Extractor 223/5.56
$6.95 -
Heat Sink, Springfield Bolt
$6.00Heat sink for use in Springfield 1903 or 03-A3 Bolt.
-
Remington 700 Bolt Disassembly Tool
$54.99Removes striker assembly in seconds for fast disassembly of all Remington bolts. Works with spring relaxed or cocked. Hook fits into the notch of the firing pin head. Rotating the lever pulls firing pin head back and locks it. Fast and easy.
-
Remington 700 Bolt Disassembly Tool
$15.00Removes striker assembly in seconds for fast disassembly of all Remington bolts. Works with spring relaxed or cocked. Hook fits into the notch of the firing pin head. Rotating the lever pulls firing pin head back and locks it. Fast and easy.
-
Shell Latch Staker
$10.00Remington 870/1100 SHELL LATCH STAKER
This tool has the correct, factory designed, rectangular swaging point to displace plenty of metal and a built-in handle, for built in control.
-
Swivel Studs, custom ball design, Intallation Tool
$21.95The premium choice for installing our custom ball swivel studs. Constructed of heat-treated carbon steel, this tool will not damage stock finish. Hex base designed to fit any standard drill chuck or 1/4-inch nut driver.
(Stud not included)
-
T Handle Reamer Extension (1/4″ round shank)
$12.50Approximately 9″ long, Comes with an adapter for standard 1/4″ round drive with set screw.
For use with standard throat reamers and rim-fire reamers with 1/4″ drive shank. T Handle -
T Handle Reamer Extension (3/8″ square shank)
$12.50Comes with an adapter for standard 3/8″ square drive (as pictured), about 9 inches long. For use with most chamber reamers.
Adapter can be removed to expose thread if you are using PTG or other tools that have a threaded drive end.